top of page

Preamp Focusrite ISA One - Analogue, bộ khuếch đại âm thanh.

- Preamp Focusrite ISA One ISA One tích hợp DI và hiệu chỉnh trở kháng đầu vào cho phép sử dụng cho micro thu vocal, capinet và guitar điện. Khả năng tinh chỉnh trở kháng là một thế mạnh của ISA One cho phép phát huy mạnh nhất các ưu điểm của các loại micro khác nhau.

- Các chức năng khác như cắt tần số thấp 75Hz, đảo pha, lọc tần số cao.

- Chức năng kiểm soát tín hiệu bằng đen LED và đèn Analog cho cả đầu vào và đầu ra

- Cho phép insert tín hiệu hoặc bộ xử lý ngoài như compressor, tích hợp headphone để kiểm tra mức tín hiệu.

Featuring a rugged, portable all-metal enclosure, ISA One combines the classic Focusrite microphone preamp with a flexible, independent DI channel and optional 192kHz precision A-D conversion. At the heart of the ISA range is the microphone preamplifier with its Lundahl input transformer – essentially the same circuit, based on the original ISA 110, that has been used for 30 years in successive Focusrite designs. The input transformer imparts a special character to the sound that can't be truly emulated in any other way, while the modern twist of variable input impedance allows for a new degree of flexibility.

Whether you're an artist, engineer or producer, you'll appreciate the versatility of the ISA One, with its front-panel DI input. The DI includes low/high impedance switching and an amplifier output, and its own feed to the optional A-D converter and separate rear-panel XLR output.

 

Preamp Focusrite ISA One

18.174.000₫Giá
  • ANALOGUE CHANNEL INPUTS

    • XLR Mic input
    • One XLR and one TRS line input
    • XLR Instrument input TRS Jack
    • External ADC input TRS Jack
    • TRS jack return

    ANALOGUE CHANNEL OUTPUTS

    • TRS jack send
    • XLR balanced line output
    • XLR DI output
    • TS jack DI through

    ANALOGUE CHANNEL ADDITIONAL I/O

    • TRS Jack cue mix left input
    • TRS Jack cue mix right input
    • 1/4" TRS Jack headphones output

    MIC INPUT RESPONSE

    Gain range 0dB to 60dB in 10dB steps + 20 dB of variable gain
    Input Impedance Switched Impedance setting Equivalent Input Impedance at 1kHz Low = 600 Ohms
    ISA110 = 1400 Ohms
    Med = 2400 Ohms
    High = 6800 Ohms
    EIN (Equivalent Input Noise) -126dB measured at 60dB of gain with 150 Ohm terminating impedance and 22Hz/22kHz band-pass filter
    Noise Noise at output with unity gain (0 dB) and 22 Hz-22 kHz band pass filter -97 dBu
    Signal-to-Noise Ratio 106 dB relative to max headroom (9dBu)
    Total Harmonic Distortion + Noise Measured at medium gain (30dB) with a 1kHz -20dBu input signal and with a 22Hz/22kHz band-pass filter < 0.0009%
    Frequency Response At minimum gain (0 dB) -0.5dB down at 10Hz and -3dB down at 125kHz
      At maximum gain (60dB) -3dB down at 16Hz and -3dB down 118kHz
    CMRR (Common Mode Rejection Ratio) 98dB (Channel 1, 1kHz, maximum gain with +24 dBu input)
    Crosstalk Channel to Channel With 10dB@1kHz input to chA, chB output =104dBrA. With 10dB@10kHz input to chA, chB output = 84dBrA

    LINE INPUT RESPONSE

    Gain range -20dB to +10dB in 10dB steps + 20 dB of variable gain
    Input Impedance 10 kΩ from 10 Hz to 200 kHz
    Noise Noise at main output with gain at unity (0 dB) measured with 50 Ω source impedance and a 22Hz - 22 kHz band pass filter -96 dBu
    Signal-to-Noise Ratio Measured with a 22 Hz-22 kHz band pass filter 120 dB relative to max headroom (24 dBu)
    118dB relative to 0dBFS (+22dBu)
    Total Harmonic Distortion + Noise Measured with a 0 dBu input signal, and a 22 Hz-22 kHz band pass filter 0.0001%
    Frequency Response At unity gain (0 dB) -0.3dB down at 10Hz and -3dB down at 200kHz

    INSTRUMENT INPUT RESPONSE

    Gain range 10dB to 40dB continuously variable
    Input Impedance High = greater than 1M
    Low =greater than 300k
    Noise Measured with 22 Hz-22 kHz band pass filter Minimum gain (+10 dB): -92 dBu
    Maximum gain (+40dB): -62dBu
    THD At minimum gain (+10)
    Frequency Response At minimum gain (+10 dB) -10dB input: 10Hz-100kHz +/- 0.6dB
      At maximum gain (+40 dB) -40dB input: -2.5dB down at 10Hz and 0dB at 100kHz

    METERS

    Moving Coil (MC) Meter factory calibrated to 0VU = +4dBu with 1kHz sinewave. With the VU Cal button pressed the meter can be adjusted on the rear panel to allow 0VU to equal +10dBu to +26dBu with the centre detent being equal to +22dBu.
    Peak LED Meters Calibrated in the detent position for 0dBFS = +22dBu, calibration is adjustable on the rear panel to allow 0dBFS to equal +10dBu to +26dBu
    Routing for MC and Peak1 meter is after the HPF, pre insert send or switched post insert return. Peak2 is always pre ADC channel 2, which can be fed by external input or Instrument input.
    LED Levels As follows, when peak calibration is set to center detent on the rear panel. (This is when using the internal ADC). 0 = +22dBu
    -2 = +20dBu
    -6 = +16dBu
    -12 = +10dBu
    -18 = +4dBu
    -42 = -20dBu
    Frequency Response At minimum gain (+10 dB) -10dB input: 10Hz-100kHz +/- 0.6dB
      At maximum gain (+40 dB) -40dB input: -2.5dB down at 10Hz and 0dB at 100kHz

    HIGH-PASS FILTER

    Roll-Off 18 dB per octave (3 pole filter)
    Frequency Fixed 75Hz measured at the 3dB down point

    WEIGHT AND DIMENSIONS

    W x D x H 220mm (W) x 104mm (H) x 254 - 290mm (D - top to bottom) 8.66" (W) x 4.1" (H) x 10" - 11.4" (D - top to bottom)
    Weight 3.9 kg 8.6 lbs
  • FREESHIP

    BẢO HÀNH 1 NĂM

bottom of page